#################################################################
#
#	MPD configuration file
#
# This file defines the configuration for mpd: what the
# bundles are, what the links are in those bundles, how
# the interface should be configured, various PPP parameters,
# etc. It contains commands just as you would type them
# in at the console. A blank line ends an entry. Lines
# starting with a "#" are comments and get completely
# ignored.
#
# $Id: mpd.conf.sample,v 1.15.2.1 2004/03/07 14:33:27 mbretter Exp $
#
#################################################################

#
# Default configuration is "myisp"

default:
	load pptp0
    load pptp1
    load pptp2

#
# Mpd as a PPTP server compatible with Microsoft Dial-Up Networking clients.
#
# Suppose you have a private Office LAN numbered 192.168.1.0/24 and the
# machine running mpd is at 192.168.1.1, and also has an externally visible
# IP address of 1.2.3.4.
#
# We want to allow a client to connect to 1.2.3.4 from out on the Internet
# via PPTP.  We will assign that client the address 192.168.1.50 and proxy-ARP
# for that address, so the virtual PPP link will be numbered 192.168.1.1 local
# and 192.168.1.50 remote.  From the client machine's perspective, it will
# appear as if it is actually on the 192.168.1.0/24 network, even though in
# reality it is somewhere far away out on the Internet.
#
# We 'set link mtu 1460' to avoid GRE packet fragmentation.
#
# Our DNS server is at 192.168.1.3 and our NT workstation is at 192.168.1.4.
# If you don't have an NBNS server (eg, NT workstation), leave that line out.
#
# Note, you can have as many of these configurations as you like, eg:
#	
#	default:
#		load client1
#		load client2
#		...
#	
#	client1:
#		new -i ng0 pptp1 pptp1
#		set ipcp ranges 192.168.1.1/32 192.168.1.50/32
#		load client_standard
#		...
#	
#	client2:
#		new -i ng1 pptp2 pptp2
#		set ipcp ranges 192.168.1.1/32 192.168.1.51/32
#		load client_standard
#		...
#	
#	client_standard:
#		set iface disable on-demand
#		set iface enable proxy-arp
#		set iface idle 1800
#		set iface enable tcpmssfix
#		set bundle enable multilink
#		set link yes acfcomp protocomp
#		set link no pap chap
#		set link enable chap
#		set link mtu 1460
#		set link keep-alive 10 60
#		set ipcp yes vjcomp
#		set ipcp dns 192.168.1.3
#		set ipcp nbns 192.168.1.4
#		set bundle enable compression
#		set ccp yes mppc
#		set ccp yes mpp-e40
#		set ccp yes mpp-e128
#		set ccp yes mpp-stateless
#
#	
# See also the 'pptp' link entry in mpd.links.sample.
#
# Note: If you cut & paste from the above example, be sure to left-justify
# the labels or else mpd won't parse them correctly.
#

pptp0:
	new -i ng0 pptp0 pptp0
	set ipcp ranges 192.168.2.254/32 192.168.2.80/32
    load pptp_standard

pptp1:
	new -i ng1 pptp1 pptp1
	set ipcp ranges 192.168.2.254/32 192.168.2.81/32
    load pptp_standard

pptp2:
	new -i ng2 pptp2 pptp2
	set ipcp ranges 192.168.2.254/32 192.168.2.82/32
    load pptp_standard

pptp_standard:
	set iface disable on-demand
	set iface enable proxy-arp
	set iface idle 1800
	set iface enable tcpmssfix
	set bundle enable multilink
# enable TCP-Wrapper (hosts_access(5)) to block unfriendly clients
#	set bundle enable tcp-wrapper
# use RADIUS servers 
#	load radius
	set link yes acfcomp protocomp
	set link no pap chap
	set link enable chap
	set link keep-alive 10 60
	set link mtu 1460
	set ipcp yes vjcomp
### 	set ipcp dns 192.168.1.3
	set ipcp nbns 192.168.2.254
#
# The five lines below enable Microsoft Point-to-Point encryption
# (MPPE) using the ng_mppc(8) netgraph node type.
#
	set bundle enable compression
	set ccp yes mppc
	set ccp yes mpp-e40
	set ccp yes mpp-e128
	set ccp yes mpp-stateless
    set pptp self 97.12.232.66

    set pptp enable incoming
    set pptp disable originate